SBS2008 설치 관련 화면을 올려 드립니다. 금번 한글 SBS2008버젼이 나와서 한글 화면을 보여드릴 수 있습니다만,
초기 설치 대부분은 windows2008설치와 거의 같은 부분이므로, 기존 영문화면 자료를 올려 드립니다.
하기 설명은 MS사 영문 Windows Small Business Server 2008 Installation Guide의 내용을
HyperV에서의 설치시 하기의 Setup으로 하시면 됩니다.
I’m installing Windows SBS 2008 from the DVD
Follow the steps in this section only if you are installing Windows SBS 2008
from the DVD. If your computer came with Windows SBS 2008 preinstalled on it,
follow the steps in the Windows SBS 2008 is preinstalled on my computer section
earlier in this document.
When default values that are typical for a small business are provided during
the installation, it is recommended that you accept these values.
Before you install Windows SBS 2008, make sure that you complete the steps in
the Before You Begin section of this document.
Step 1: Install the operating system
Windows SBS 2008 first installs the operating system, and then you provide
information about your organization that is used to configure the operating
system and to finish the installation.
After the operating system is installed, do not customize your server until
you finish "Step 2: Configure the Windows SBS 2008 operating system."
Estimated completion time: Approximately 30 minutes. (Estimated completion
times throughout this procedure are based on minimum hardware requirements.)
To install the operating system
1. Connect your computer to your network with a network cable.
Installation may fail if you disconnect your computer from the network.
2. Turn on your computer, and then insert the Windows SBS 2008 DVD into the
If you are performing an unattended installation, connect the removable media
(such as a floppy disk or a USB flash drive) that contains your answer files.
Depending on the contents of your answer files, you may not see some or any of
the following installation screens.
3. Restart your computer. When the message “Press any key to boot from CD or
DVD” appears, press any key.
If your computer does not start from the DVD, ensure that the CD-ROM drive is
listed first in the BIOS boot sequence. For more information, see the
documentation from the computer manufacturer.
4. Select the Language that you want to install, Time and currency format,
and Keyboard or input method, and then click Next.
5. Click Install now.
6. Type your product key in the text box, and then click Next.
MS SBS2008의 Product Key는 일반 설치 Key와 Hyper-V Key가 구분이 되어져 있습니다.
설치시 Product Key가 바뀌어도 이후 진행이 되는지는 아직 확인 하지 못하였습니다.
7. Read the license terms. If you accept them, select the I accept the
license terms check box, and then click Next.
If you do not choose to accept the license terms, the installation does not
8. Click Custom (advanced) to select where you want to install the Windows
9. Create a partition (if necessary), and then select the partition where you
want to install the Windows operating system.
a. If a hard disk is not listed (for example, a Serial Advanced Technology
Attachment (SATA) hard disk), you must load device drivers. Obtain the device
driver from the manufacturer and save it to removable media (such as a floppy
disk or a USB flash drive). Attach the removable media to your computer, and
then click Load Driver. After the driver is loaded and the hard disk is listed,
complete either c. or d. in this step.
If you decide that you do not need to load any device drivers to access your
hard disk, on the Select the driver to be installed page, click Back to return
to the Where do you want to install Windows page.
b. If you are installing Windows SBS 2008 on a computer that is running a
Windows operating system that does not support an upgrade, it is recommended
that you delete the system partition, and then re-create new partitions. When
you delete a partition, any existing data on the partition is permanently lost.
To delete a partition, select the partition, click Drive options (advanced),
and then click Delete. After you delete the system partition, create a partition
by using the instructions in either c. or d. in this step.
After you click Drive options, you will not see it again. In that case, just
skip that part of the step which refers to Drive Options.
c. To create a partition from an unpartitioned space, click the hard disk
that you want to partition, click Drive options, click New, and then in the
Partition size text box, type the partition size you want to create. For
example, if you use the recommended partition size of 60 gigabytes (GB), type
61440, and then click Apply. After the partition is created, click Next. The
partition is formatted before the installation continues.
d. To create a partition that uses all of the unpartitioned space, click the
hard disk drive that you want to partition, click Drive Options, click New, and
then click Apply to accept the default partition size. After the partition is
created, click Next. The partition is formatted before the installation
You cannot change the partition where you install the operating system after
you finish this step. You must reinstall Windows SBS 2008 if you want to change
For more information, see the “Disk Management” section in “Planning Your
Windows Small Business Server 2008 Network” at the Microsoft Web site
During the installation, temporary files are copied to an installation folder
on your computer, which takes about 15 minutes. After the Windows SBS 2008
operating system is installed, your computer restarts. Now, you are ready to
configure the Windows SBS 2008 operating system.